EZForms

Concrete formwork you bolt together.
CNC-cut PVC panels, made in Pretoria.

Shop EZForms Request a quote →

One kit, every pour

The same panels and corners shutter a column, a slab and a plinth.

Line drawing of an 800 by 800 mm column shuttered with four upright EZForms panels and corner pieces
Column800 × 800 × 1200 mm · 4 panels, 8 corners
Line drawing of a slab deck of six EZForms panels laid face up on bearers and props
Slab deck2400 × 1800 mm · 6 panels on props
Line drawing of a 2600 by 1400 mm plinth shuttered with six EZForms panels and four corner pieces
Plinth2600 × 1400 × 600 mm · 6 panels, 4 corners

Products

Start with the standard panel and corners. More sizes, bracing and complete kits are on the way.

Standard wall panel

1200 × 600 × 100 mm

The building block of the system. Ribbed PVC box with a smooth face, handles cut in, and the standard bolt pattern on all four edges.

Shop panels
Line drawing of the EZForms corner piece, 200 by 200 by 600 mm, with bolt flanges on both legs

Corner piece

200 × 200 × 600 mm high

A pre-formed 90° corner that bolts onto the end of a wall run, so corners come out square without cutting.

Shop corners
Our CNC router with a full sheet of panel parts

Custom panels

Cut to your drawing

Need an odd height, a column box or a step? We cut panels to your dimensions on our CNC router.

Request a quote

How it works

  1. CNC router bed with EZForms panel parts nested and cut1

    CNC cut

    Panels are cut and drilled on our CNC router in Pretoria, so every hole lines up.

  2. EZForms panels bolted into a long foundation shutter on site2

    Bolt together

    Stand the panels up and bolt them into walls, corners and plinths with basic hand tools.

  3. Formwork set up with reinforcing steel ready for the pour3

    Pour

    Brace, fix the reinforcing and pour. The ribbed panels take the pressure.

  4. Completed retaining wall cast with EZForms panels4

    Strip and reuse

    Unbolt, wash and stack the panels for the next pour. The concrete keeps a clean, even face.

Why EZForms

01

Light enough to carry. Strong enough to pour.

Each panel is a ribbed PVC box, not a flat sheet: a smooth face backed by stiffeners. One person carries a panel, two people build a wall. No crane on site.

02

One bolt pattern. Every shape.

Panels and corner pieces share the same hole pattern, so they bolt together in any direction: plinths, foundations, walls and columns from the same kit.

03

A clean off-shutter finish.

PVC doesn't soak up water, swell or warp, so the face stays flat and smooth from one pour to the next. No release oil needed.

04

Strip it, wash it, use it again.

Unbolt after the pour, hose the panels down and stack them for the next job. Formwork that stays an asset, not a cost.

A bakkie loaded with a full set of EZForms panels, strapped and netted

A whole garage foundation on one bakkie.

No flatbed, no crane. Load the panels by hand, strap them down and drive to site.

A ratchet and a spanner resting on bolted EZForms panels
A ratchet and a spanner. That's the toolkit.

Projects

Our first panels went straight onto a mine: the foundation and wall of a retaining wall for Anglo American, in 2025.

The completed retaining wall at the mine, cast with EZForms panels
Retaining wall for Anglo American (now Valterra Platinum), 2025. Foundation and wall cast with EZForms.

Retaining wall, Anglo American

Client
Anglo American, now Valterra Platinum
Scope
Foundation and wall shutters
Panels
1200 × 600 × 100 mm, bolted
Year
2025

The foundation shutters were bolted together on the ground, the wall forms went up against the scaffold, and the panels were stripped and reused down the length of the wall.

Foundation shutter assembled on site Wall formwork standing against the scaffold Long run of foundation shutters Formwork and scaffold on the retaining wall Triangular braces holding the shutters Completed section of retaining wall
EZForms name engraved into a panel by the CNC router

Made here

Cut in Pretoria, on our own CNC router.

We draw, nest and cut every panel in-house, from the bolt holes to the handles to the name on the face. That's how we keep the hole pattern exact and the lead times short.

Finished panels stacked and ready for dispatch

Build your next pour with EZForms.

Shop EZForms on Buildalot WhatsApp for a quote

062 049 0300 · admin@megastructures.co.za · 131 Fusie Street, Silvertondale, Pretoria